Dynacord Xa2
Passive PA-Speakers Dynacord Xa2Passive PA-Speakers Dynacord Xa2 (2)Passive PA-Speakers Dynacord Xa2 (3)Passive PA-Speakers Dynacord Xa2 (4)Passive PA-Speakers Dynacord Xa2 (5)

Dynacord Xa2

  • Subcategory: Complete PA set
  • Design: Sub: Rectangular, Top: Rectangular
  • Components: Sub: 18" LF-/12" MF-/1" HF-driver
  • Power (watts rms): Sub: 600 Watt, Top: 350 Watt
  • Impedance: Sub: 8 Ohm, Top: 8 Ohm
  • Frequency range: Sub: 30 Hz to 150 Hz; top: 120 Hz to 19 kHz
  • SPL ( 1w/1m): Sub: 101 dB; Top: 106 dB
  • Max. SPL ( 1 W/1 m): Sub: 132 dB; Top: 134 dB
  • directional characteristic: 80° x 40°
  • Internal cross over: no, active seperation
  • Connections: 2x Neutrik Speakon NL4
  • Enclosure: Sub: Multiplex, black; top: multiplex, black
  • Flyability: Sub: no, top: yes
  • Pole flange: No
  • Special features: Consists of 4x Tops and 2x Subwoofer and 2x System poweramps/Controller, 4x Speakonkabel (4 m) and 2x Speakonkabel (15 m)
  • Dimensions (WxHxD): Sub: 610 x 905 x 814 mm, Top: 600 x 610 x 814 mm
  • Weight: Sub: 47,5 kg, Top: 48 kg
Item number: 2415140
Available soon
Available in 7-14 business days

Bulky goods
This item is shipped by freight carrier. [further information]

01/2005
Available since:

Print view
Lowest Price Guarantee

Dynacord Xa2 · Passive PA-Speakers

FX 12 top/mid-range

Features:
  • Type: 2-weg mid/high cabinet
  • output power : 350 watts/RMS
  • Max. SPL (1W / 1 m): 106 dB
  • Nominal impedance : 8 ohms
  • Frequency range: 120 Hz – 19 kHz (-10 dB)
  • Components: 12“ woofer, Directivity Horn using a 1.4" neodymium driver
  • Dimensions: 600 x 610 x 814 mm
  • Weight: 48,00 kg
  • enclosure is finished with black, extremely heavy carpet

The DYNACORD FX 12 is concepted as a medium longthrow mid/high- frequency cabinet in coaxial design. It can be used also without subwoofer cabinets in high-quality sound reinforcement system for speech for medium-throw distances. The recommended active x-over frequency is 140 Hz, 18 dB/oct. Butterworth. In the lo-mid range an ND 12 An Electro-Voice loudspeaker chassis works into a conical horn. The 80x40 Constant Directivity horn, driven by an Electro-Voice 1.4" ND 6 neodymium driver delivers the frequency range above 1kHz. The FX 12 is equipped with a passive x-over (1kHz, 18 dB/oct). Every transducer is protected against thermal overload with an electronic circuit called VOICE COIL TRACKING PROTECTION. Power amps up to 1200 watts 8 ohms can be used in order to have maximum dynamic range without the danger of thermal overload in non-controlled situations. The VOICE COIL TRACKING PROTECTION exhibits ‘soft’ switching characteristics, so no annoying clicks or pops are audible.

The FX 12 cabinet is made of 15mm poplar plywood. All corner joints and braces are grooved and glued in order to reduce cabinet resonances to a minimum. The cabinet surface is covered with a heavy-duty black carpet like Tolex. A powder-coated steel grille and an acoustic foam front protects the speakers. The connector panel uses two 4-pole Speakon connectors (Input/Output) for safe connection and easy chaining to the next loudspeaker.

The handle trays on the sides guarantee easy and safe transport. 4 large-sized rubber feet and 4 castors allow easy handling and a safe stand. 4 integrated rigging tracks and 2 webbing strap-points can be used for easy ‘flying’ of the FX 12 cabinets.

FX 20 Subwoofer

Features:
  • Type: planar waveguide basshorn
  • output power : 600 watts/RMS
  • Max. SPL (1W / 1 m): 101 dB
  • Nominal impedance : 8 ohms
  • Frequency range: 30 Hz – 15 kHz (-10 dB)
  • Components: 18“ woofer
  • Dimensions: 610 x 905 x 814 mm
  • Weight: 47,50 kg
  • enclosure is finished with black, extremely heavy duty carpet Tolex

The DYNACORD FX 20 is a Planar Waveguide Basshorn, equipped with the high-power Electro-Voice EVX 180B 18" transducer. Frequency response is 30Hz - 150Hz (-10dB), so the crossover frequency to Mid-Hi cabinets can be chosen strictly application-oriented between 80Hz and 140Hz. The cabinet is equipped with an electronic circuit called VOICE COIL TRACKING PROTECTION. This circuit senses the terminal voltage of the transducer and simulates the thermal behaviour of the woofer´s voice coil. In case of potential thermal overload the power applied to the speaker is reduced to a safe level. Power amps up to 1200W/8Ohms can be used in order to have maximum dynamic range without the danger of thermal overload in non-controlled situations. The VOICE COIL TRACKING PROTECTION exhibits “soft” switching characteristics, so no annoying clicks or pops are audible. The circuitry automatically resets after the voice coil temperature has reached a safe value.

The FX 20 cabinet is made of 15mm poplar plywood. All corner joints and braces are grooved and glued. The cabinet surface is covered with a heavy-duty black carpet. A powder- coated steel grille and an acoustic foam front protects the speakers.

The connector panel uses two 4-pole Speakon connectors (IN/OUT) for a safe onnection and easy daisy-chaining to other cabinets. The pin assignment is +/1-. Pins 2+ and 2- are also connected between the respective two Speakon onnectors. When using DYNACORD power amp racks or system amplifiers, the whole system can be wired with 4-pole Speakon cables without any danger of accidental wiring mistakes. The cabinet is equipped with eight large rubber feet that allow easy stacking. Six handles and four heavy-duty castors on the rear side guarantee easy and safe transport.

Xa 4000 System power amp

Features:
  • Class H technology and a switching power supply.
  • Power to 8 Ohm: 2 x 600 watts
  • Power to 4 Ohm: 2 x 1100 watts
  • Power to 2 Ohm: 2 x 1800 watts
  • Input: symmetrical XLR
  • Outputs: Speakon
  • Protection : Audio limiters, High temperature, DC, HF, Back-EMF,
    Peak current limiters, Inrush current limiters, Turn-on delay
  • Dimensions: 19“/2U, depth 38.4 cm
  • Weight: 8.25 kg

The universally usable Xa 4000 active 2-way power amplifier provides Class H technology and a switching power supply. Xa 4000 power amps combine outstanding audio performance, highest reliability and operational safety allowing easy setup and operation of active 2-way systems with a crossover frequency of 140Hz between bass and mid/high cabinets.

The power amp’s output capacity of 1100W/4ohms for the bass channel and 900W/4ohms for the mid/high channel allows the connection of up to four 8ohms cabinets per channel. The integrated frequency crossover separates the bass from the mid/high range at 140Hz.

Optimized for the usage of medium sized and large-format vented bass cabinets, bass horn speakers, Manifolds and Planar Waveguide horns, the LPN – Low-Pass-Notch filters – bass equalization corrects the transient response of connected bass cabinets.

The speaker outputs of the power amps are carried out as SPEAKON connectors (female). The pin-assignment of the system connector is: bass channel via pins 1+ and 1-, mid/high channel via pins 2+ and 2-. The use of 4-core speaker cables allows for convenient, quick and easy as well as mismatch-proof setup of loudspeaker systems. Separate SUB and TOP Speakon-sockets are provided in addition to the system connector. The output signal at these connectors is present at pins 1+ and 1-, which allows easy connection of basically any type of speaker system, even if it provides no system cabling facilities.

Range of use:
  • Top-40 Indoor/Outdoor Live Events
  • High Power mobile DJ events
  • High Quality corporate events
  • High-Power speech reinforcement

  • Multimedia events

  • Theatre applications
  • Rental companies
  • Fixed installations


Components:
  • 2x Xa 4000 System amp´s / controller
  • 2x FX 12 tops
  • 4x FX 20 subwoofer
  • 4x PSS 404 speakon cable 4m
  • 2x PSS 415 speakon cable 15m

For a great flexibility regarding events and venues these Xa-2 components can be set up without complex settings, controller adjustments or limiter calculation. Just check in which variation you need and set up the needed configuration.

If more bass is needed at the Open-Air DJ-Event, then just install a extra sub at each side if the brass band needs further throw take away a sub and use 2 tops set at an angel and if the TOP-40 Band is suddenly playing to 4000 people, the same system will power 3 Sub’s, 2 Tops and additional front- or sidefills, no problem !

Passive PA-Speakers · Dynacord Xa2

No review for this product available.
Be the first to rate this product!

Downloads: Dynacord Xa2, Passive PA-Speakers

Dokumente
  • (EDS-FX12.pdf)
  • (EDS-FX20.pdf)
  • (EDS-Xa4000.pdf)
  • (Xa-Brochure d.pdf)
  • (00-C0NFIG-00.pdf)
  • (01-EXTENS-01.pdf)
  • (02-EXTENS-02.pdf)
  • (03-EXTENS-03.pdf)
  • (FG 600 3x FX 12.pdf)
  • (FG 600 SPLAYED.pdf)
dep_pa
Martin Diekmann
Order Hotline
Tel.: +49 (0) 54 51/9 09-0

Advice & Support
Tel.: +49 (0) 54 51/9 09-120
pa@musik-produktiv.de

Find similar products:
· Dynacord Passive Loudspeakers
· Show all articles of the brand Dynacord.
· Category: Passive Loudspeakers
· Loudspeakers
· PA Sets
· Mixing Desks
· Powered Mixing Desks